Manual welding extruder RSE-1

Dear customer,

we Express our gratitude to you for purchasing our product Manual welding extruder RSE-1. We have a powerful laboratory of 1000 m2 and a large production base, we produce various products! The main direction is manual welding extruders, our equipment is represented on the world market. There are copyright certificates and patents. Our equipment works on many sites and we also work with our own equipment. Delivery throughout Russia and the CIS.

To purchase a manual welding extruder of RSE-1

Performance Up to 2 kg / hour
Filler material PP, PE
Hopper capacity 0.25 kg
Sheet thickness up to 30 mm
Joint width 3...15mm In
Price 43,000 rubles

Welding extruder of RSE-1

 

Purpose of the product.
Permanent connection of parts (sheets, pipes, profiles) made of thermoplastic polymer materials by feeding a homogenized mass of filler material into a heated bath formed by the edges of the parts to be connected.

 

Application
Production of pipelines, aeration systems, tanks, septic tanks, sheet and film structures for various purposes, elimination of defects in plastic products, etc.

 

Principle of operation
The filler material (PE granules, PP, crushed waste) is poured into the Loading Hopper (5) (see Fig. 1), from where it is captured by the screw (1) through the receiving hole in the Sleeve (2) and enters the heating zone, passing through which it acquires a plastic state. Hot air supplied from a special device (11) through a pipeline (9) is used as a heat carrier in. The screw rotation drive (10) is an Electromechanical mixer installed in the mandrel (6).

 

Filler material is fed into the welding zone through the hole of the Welding Nozzle (3). The heating of welded parts in the welding zone by hot air, which enters under pressure through the outlet of the Heating Chamber (4). On the Casing (2) For the convenience of the product is provided with a Handle (8). The parameters of the weld are determined by the parameters of the cross section of the outlet of a replaceable Welding Nozzle(3).

ATTENTION! Preparation for work.
Before starting work, warm up the mechanism for 7-10 minutes!
Important! Pay attention to how warm your nozzle (Shoe) is) The nozzle must be warmed up very well, so that the nozzle does not form a cork from the frozen extrusion.
Fill the feed hopper with the filler material.(fraction of 3-4 mm)

 

ATTENTION! It is not allowed to use non-crushed waste as an additive material, as well as foreign particles (metal, wood, etc.) entering the loading hopper. Such violations may cause the screw to break or jam and cause the drive to fail.
Set the heating and air supply device mode «warm-up» (2) to the maximum temperature( about 530 deg.), and let the device work for 7-10 minutes.

Note: (the 1st mode of the air supply speed on the hair dryer is used when welding thin (1mm) materials. The air flow is not large, thus there is a gentle heating. The sheet does not deform …

note:
for welding plastics, set the temperature on the hair dryer a little more.. (When the hot air comes out of the extruder nozzle, it connects with the surrounding air, and a small error is obtained on the nozzle. Weather conditions must be taken into account.
The product is ready for use.

 

Operation
Make a test seam. During operation, visually monitor the quality of the weld. If it is necessary to temporarily stop working (for example, to fill the material into the loading hopper), the extruder should be switched to (0) mode. When resuming operation, re-set the operating mode (2).

 

Security measures
The product meets all requirements that ensure the safety of life and health of the consumer, as well as environmental protection.
Keep in mind that the temperature of the extruded mass of the filler material, as well as the temperature on the surface of the welding nozzle and the heating chamber during operation is at least 150 degrees Celsius.
It is not allowed to operate the product with the lid of the loading hopper removed, as well as to clean the hopper when the power supply to the screw drive is turned on

It is forbidden: to Work without grounding, to work in wet weather, to work with faulty wiring, to use the extruder for other purposes, to work without a certificate or other authorization document for training with a manual welding extruder, to leave it unattended,to work without preheating the extruder(there is no protection against «cold start»), to make any changes to the design. It is forbidden to work near explosive liquids, compounds, objects, unstable position of the operator and the structure being welded. It is forbidden to transfer the extruder to an untrained and untrained person who does not have a permit.. It is forbidden to work in the dark, or in poor light. It is forbidden to work with materials that emit toxic substances.

 

Guarantee of long-term operation of the equipment and the quality of the weld.

Recommendations

Welding extruder

Any welding extruder consists of two main components. The first is the heater that melts the plastic, the second component is the directly feeding part or the extrusion part of the welding extruder.

Do not forget that different plastics melt at different temperatures, so a high-quality welding extruder has a heating temperature control unit.

Use only high-quality welding material to work with a manual welding extruder, thus you will get a high-quality strong and sealed seam.


The price of the extruder (RSE-1) is 43,000 rubles.

The set includes 5 shoes.

The price of an additional nozzle (metal) for Your tasks is 800 rubles.

The price of an additional nozzle (fluoroplast) is 2500 rubles.

Products Manual welding extruder RSE-1 NO. 019602710-061I.

Warranty repair of the mechanical part of the extruder for 1 (one) year if there is a seal.

Warranty service does not apply to the hair dryer and mixer. The hair dryer can be installed by any manufacturer and any price category. The seat is 40mm. The power of the hair dryer is not less than 2000 watts.

Technical specifications-page 3

Manufacturer of products Engineering and technical center (SP Matveev S. V.)

Instructions 4 (four) sheets.

Date of manufacture 20.07.2019

Address: Shchelkovo, ul. Belyaeva 29 St. 1 Tel: 8-499-955-45-92; 8-985-000-64-65

Ручной сварочный экструдер РСЭ-1

Copyright certificate

Экструдеры Патент
Декларация о соответствии Лабораторные Z
Декларация о соответствии РСЭ
Ручные сварочные экструдеры

Extruders

 

To purchase a manual welding extruder

 

Our engineering and technical center produces manual welding extruders for welding plastics.

Manual welding extruder from the factory ITTs-Extradermal, reliable machines manufactured in Russia.

To view
Инженерно-Технический центр «ЭкструдерМаш»
Модельный ряд РСЭ

A manual extruder is a reliable machine that cooks with pellets or a bar.

Модельный ряд Лидер

Manual extruder «Leader» is a new group of the model range in 2020.

Сварочный пруток

This is the filler material used to form the welding seam.

Насадки для ручных экструдеров

Form the configuration of the seam from the molten mass (extrusion). We have about 20 attachments.

Manufacturer of manual extruders

 

Engineering and technical center «Ekstrudermash» is engaged in welding manual extruders razrabotkoi (Leader-1, Leader-1M, Leader-2, Leader-3, Leader-4, Leader-5, Leader-6, RS-1, RS-1M, RS-3, RS-5, RS-6, Ural-1, Ural-2, Ural-Ural I. 3-3P) muvyr welding of plastics.

ITTs-Extradermal is located in Schelkovo, Moscow region

Доставка экструдеров

Please fill out the feedback form and we will contact you or just call!

we Carry out orders for any individual development, please contact us we will design any individual project.

ИТЦ-Экструдермаш

Call now


Delivery is carried out throughout Russia and abroad.

Any questions?

You can get all the details from the head of the company Матвеева Сергея Владимировича

× Как я могу Вам помочь?